Electric floor heating type

A: Heating cable heating is divided into single-conductor and double-conducting. From the perspective of electromagnetic radiation, the double-conducting cable is smaller than the electromagnetic radiation of the single-conductor cable, which is more suitable for household floor heating, and the single-conducting electromagnetic radiation is better than double The guide is higher, and it is used in outdoor floor heating systems. In terms of design and installation, the single guide is more difficult. Since both ends of the single-conductor cable must be connected to the thermostat, it is necessary to properly return the end of the cable, so that it needs to be designed at the time of design. Master the scale. Compared with single-guided double-conductor, it is better to construct, and the end can be cut off at the end.

B: The electric heating film heating system is composed of a temperature controller, a connecting wire, a connecting card, an insulating auxiliary material, a heat insulating material, an electric heating film and a facing material. The electric heating film is a heating element of the floor heating system. After the electric heating film is connected to both sides, the positive and negative electrodes generate a voltage difference to form an electromagnetic field. The carbon molecular crystals perform Brownian motion in the alternating electromagnetic field, and friction and collision generate heat and emit far infrared rays. The light wave radiates heat evenly to the room from the floor, and at the same time, under the effect of the difference in specific gravity of the hot and cold air, the natural convection phenomenon of the air is generated, thereby achieving a stepwise heating effect.

C: The carbon crystal floor heating system is mainly composed of three major components: a carbon crystal heating plate, a thermal insulation plate, and a thermostat. The carbon crystal plate is synthesized by flame retardant resin, insulating resin and oxidized resin under high temperature and high pressure, so it has the characteristics of non-combustible, non-conductive, anti-oxidation and strong. Carbon crystal floor heating is the use of electricity to conduct Brownian motion through the carbon crystal molecules to do the Brownian motion to obtain heat. This heating method makes full use of the three modes of heat transfer: heat conduction, heat convection and heat emission.

D: Carbon fiber electric floor heating carbon fiber floor heating system is mainly composed of three major components: carbon fiber heating plate, insulation board, thermostat. The carbon fiber heating plate is synthesized by flame retardant resin, insulating resin and oxidized resin under high temperature and high pressure, so it has the characteristics of non-combustible, non-conductive, anti-oxidation and strong. Carbon fiber floor heating is the use of electricity to generate heat through the movement of carbon fiber molecules to do Brownian motion.

E: Warm core flooring is an emerging heating method, also known as an emerging heating equipment. The warm core floor is a kind of "floor heating two-in-one" heating system which is different from plumbing, electric heating film and heating cable. It is the latest high-efficiency, energy-saving, environmentally friendly, low-carbon thermal energy conversion material that can be used in aerospace, technology, and civil applications. It can also be called "warm core self-heating floor" or "temperature-controlled self-heating floor".

G: Filament carbon fiber heating cable is a new type of high-tech product. It quickly drops to the freezing point at a temperature of 2000 degrees Celsius for 0.07 seconds. Filament carbon fiber floor heating is a non-metallic material. The filament carbon fiber heating cable can be heated for 3-5 seconds. The carbon molecules in the carbon fiber after energization are "Brown motion", no electromagnetic radiation, no heat decay. The body feels warm in the room for 15-30 minutes. The general heating cable will generate an electromagnetic field as long as it passes through, and the electromagnetic field that is harmful to the human body in the process of canceling each other. The magnetic field is relatively reduced. There is also thermal attenuation. After a long time, a layer of oxide will appear on the surface, so that the heating rate is greatly reduced, and the heat is not evenly distributed. Slowly, it feels that it has not started to work. After the metal wire is energized, due to its own The heat of the resistor is generated, and the heat is transmitted to the form of the heat. The heat-generating cable has a hard texture. If it is bent many times during the construction process, it will be destroyed. This is required to be very careful during the construction process. Bend the cable multiple times. There is a phenomenon of uneven heat generation and short circuit. The electromagnetic wave radiation generated during use is long-term in such an electromagnetic wave field, which has microscopic adverse effects on people. After the carbon fiber heating cable is energized, the hot wire heats up and penetrates the medium. The whole heating process is silent, no light, no electromagnetic radiation, no pollution, energy saving and environmental protection. The heat conversion conversion rate can reach up to 98.2%, which is 30% higher than the wire heat. Under the same current load, the strength of the carbon fiber is 10 times that of the wire, and it does not break, and it can not extinguish the fire. lasting. It will not be short-circuited in the water, and the hand will not be charged. Because it is non-metallic, there is no current and voltage on the surface. It is safe. It runs at 40 to 60 degrees and becomes far-infrared low-temperature radiant heating. The service life is the same as the length of the building. As long as it is not damaged, it can guarantee normal operation for more than 50 years, and basically no maintenance is required. The long-fiber carbon fiber electrothermal conversion rate is as high as 98%. In other words, they were also given once, only 0.70 kWh through the wire, and 0.98 kW through the long-fiber carbon fiber. Therefore, in terms of operating costs, carbon fiber electric floor heating is 30% less than wire electric floor heating. Compared with the electromagnetic radiation of the metal wire, the carbon fiber is electrically heated to the opposite extent. The 4-17m far infrared radiation it radiates is extremely beneficial to the human body and is called "life light wave". It is commonly used in the medical profession to treat people with physiotherapy, and the effect is very good. Therefore, the use of carbon fiber electric floor heating can not only bring you warmth, but also bring you health.

Electric floor heating background

Ground low-temperature radiant heating technology has been widely used throughout Europe, North America (Northern United States and Canada) since the 1950s, and its history can be traced back to the Roman Empire, when people introduced underground hot springs into underground tanks. Electric floor heating under the marble floor to heat and heat. There have been similar applications in ancient Chinese royal palaces.

The ground low-temperature radiant electric heating system is the most comfortable, healthy and increasingly popular heating method in the world. With a service life of more than 50 years, you can choose to use the floor heating system in all areas of your home. You can also choose to use it in some areas (such as bedrooms and halls). )use. The electric floor heating system has been widely accepted and recognized in the vast areas of Europe and North America. With the improvement of the living standards of our people, this new type of heating has also been applied more and more in China. Floor heating began to enter people's home life. . .

Coated Polyester Geogrid ( PET )  : Ultimate Tensile Strengths from 25kN/m to 1200kN/m ), PET ( Uniaxial geogrids ) and PET  ( Biaxial geogrids ) : Ultimate tensile strengths from 25KN/m to 1200KN/m. 

 Polyester uniaxial & Polyester bi-axial Geogrid range: Flexible uniaxial or biaxial geogrid constructed of high tenacity , high molecular weight PET – Polyester with black PVC saturation coating by using the state of art knitting process .


1. It reinforce old asphalt concrete road surface and asphalt layer, and prevents damage ; 

2. It is used for rebuilding cement concrete road surface into composite road surface and restraining reflection caused by block contraction . 

3. It is used in road expansion and improvment project and crack caused by old and new combination position and uneven sedimentation ;  

4. It is used in soft soil base reinforcement treatment ,  is favorable for soft soil water separation and concretion,restrains sedimentation effectivly,distributes stress uniformly and improve overall strength of road base; 

5. It is sued for preventing contraction crack caused by new road semi-rigid base layer,and reinforces and prevents road surface crack caused by foundation crack reflection. 



Polyester Geogrid

Warp Knitted Polyester Geogrid, Pvc Coated Uniaxial Polyester Geogrid, Pvc Coated Pet Uniaxial Geogrid, Polyester Geogrid For The Roads

Feicheng Lianyi Engineering Plastics Co., Ltd , http://www.lianyigeosynthetics.com